Baslinux mailing list

[Constant Brouerius van Nidek <constant AT indo.net.id>]

Finaly got so far as to connect my P100 with my Pentium II.
On the P100 I run BL2, on the Pentium II SuSe 8.1.

I have called my home network constant.net
The P100 is called p100 and the Pentium II is called bigone.
I have a dialup to my isp and I am running postfix on the bigone.
Mailtransport from p100 should run via bigone. The two are connected 
with a twisted cable.

I have the feeling that something is not right or missing. Have no 
idea what or where so I have attached the results of my search.
What is wrong and where do I have to repair it?

Both ethernet cards are recognised. The email transport via the dial 
up from bigone works. 
Pinging from the one to the other is not working.
Resulting info from ping from p100:

PING bigone.constant.net (192.168.1.1): 56 data bytes
ping: sendto: Network is unreachable

from Suse (bigone) I get more or less the same info:

PING p100.constant.net (192.168.1.2) from 192.168.1.1 : 56(84) bytes 
of data.
From bigone.constant.net (192.168.1.1): icmp_seq=1 Destination Host 
Unreachable

route -n gives me following for bigone:

Kernel IP routing table
Destination  Gateway     Genmask       Flags Metric Ref    Use Iface
192.168.1.0   0.0.0.0     255.255.255.0   U      0     0       0 eth0

p100 gives following:

Kernel IP routing table
Destination  Gateway     Genmask   Flags Metric Ref    Use Iface
127.0.0.0     0.0.0.0         255.0.0.0   U     0      0        0   lo

ifconfig -a for the Suse box gives following info:

eth0      Link encap:Ethernet  HWaddr 00:50:BA:C0:36:BA
          inet addr:192.168.1.1  Bcast:192.168.1.255  
Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:18 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:0 (0.0 b)  TX bytes:1080 (1.0 Kb)
          Interrupt:3 Base address:0x300

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:56 errors:0 dropped:0 overruns:0 frame:0
          TX packets:56 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:4624 (4.5 Kb)  TX bytes:4624 (4.5 Kb)

the ifconfig -a for the BL2 box has this info:

dummy     Link encap:Ethernet  HWaddr 00:00:00:00:00:00
          BROADCAST NOARP  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 iB)

eth0      Link encap:Ethernet  HWaddr 00:50:BA:C0:2F:90
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 iB)
          Interrupt:9 Base address:0x320

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:3924  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 iB)  TX bytes:0 (0.0 iB)